11/10/2023. Come a cross a dirty RC in Facebook sale just put in for sale few minutes. Just chassis, body cover, with electric parts but very dusty. Look like HPI E10, from the motor and receiver return HPI. Sale for Rm150, meet up in Lotus ockland seremban 2 is a ori E10. History this rc buy new for him, but look on condition problem after playing put a side until dusty. He use 2 pcs 7.2v battery joint pareller give more powerful amp but it will damage the ESC. He using Vantex ESC. He say problem in electrical. Given HPI ori remote. Back home check and dismental parts look for damage parts.
After gone through Internet this is HPI E10 Touring car RTR 10725 Nissan Skyline R32 GTR 2011. The best on this brand, we can change position motor and mounting location rear to front. To suiet driving position driff or touring.
Start blogger = 11/10/2023
Update bloog = 30/12/2024
Total Spending parts = Rm48.20.
2011-2025 (14 years)
Made in USA (🇺🇸)
 |
Image From saller |
 |
Very dusty |
The original image
 |
The driff box not my |
 |
The ori electric set |
 |
Ori HPI ESC |
 |
Motor can shift from rear to front Touring or driff. The diffrential also need tu change position. |
 |
This is 2007 instruction manual can be use. 2010 manual same, can't find assembly manual only over view. |


The car condition after checking
1. All screw rusty
2. All wheels hub no ballbearing
3. Broken push rod for steering super glue
4. Battery joint not solder
5. Bottom chassis heavy scratch
6. Body cover paint damage
7. Battery tamiya connectors missing
8. Both battery cable tide on chassis
9. Drive shaft super glue on spur gear.
10. Extra negative wire from battery to receiver
11. Full of dust and paint drop.
12. Front lhs/rhs dummy brake disc out of position.
13. Front and rear axle gear no greese
14. Missing 1pcs front dogbone
15. Missing antenna on remote
16. Motor negative wire joint no sholder, twis togather.
17. Missing 1 pcs differential cup front rhs 88001.
18. No battery holder
19. No battery holder post
20. Center proppeler shaft been modified use superglue and alu pipe.
21. Rear shock top mounting been modified
22. Reciever wire break
23. Steering servo bracket too tight hard to remove screw
24. Steering not using turn buckle
25. Suspention shaft and step screw with dirty surface hard movement.
26. Using 2 pcs 7.2v battery joint pareller to get move power.
27. Vantex ESC faulty
28. Wheels been spray white, chip.
 |
Ori red but add white outside damage, will remove it. |
 |
Bumper crack stapler. Head lamp cut out |
 |
Rear bumper crack |
Ori radio system TF-1, still function can on only missing antena is a 72 am channel




 |
The small shaft superglue on spur gear |
 |
Surfaces step and shaft screw dirty, movement suspention not smoooth. |
 |
All wheels fitted ballbearing |
 |
Rear axle done |
 |
Front axle done |
 |
The DIY dogbone and diff cup |
 |
Rear damper fitted nicely on the original position. |
 |
The battery holder from HSP |
 |
Battery holder post from HSP |
 |
I change to adjustable linkage |
 |
Put back the same electric parts not going to run this rc. |
Two same RC ori and Clone HPI E10
 |
Lhs ori, Rhs clone |
The white paint remove. Top i will respray white. Body need repolish and crack body reglue.
 |
Top will respray white. |
 |
Front bumper inside reglue few layer |
 |
Top done respray white |
Body Done rework
5/11/2023 got the same size antenna rm2.30
Soon image
Comments