After buying my Kyosho Buggy there is a problem the all 4 wheel is wobble when in full speed where the wheel not touching the ground. To solve this problem the wheel need some balancing. So look into the net found HUDI Wheel Balancing Machine look nice and expensive. I am not joining any competition, i am just to have fun, not practical to buy one, seldom use. So look into my RC Loose parts then this idea came to build my own DIY RC Wheel Balancing. No cash flow out from my pocket.
Start bloog = 26/08/2018
Last update bloog = 07/10/2020
 |
| Second DIY upgrade |
First DIY
 |
| This is my Kyosho Spider Rear Lower Arm |
 |
| This is a Kyosho Spider Real Wheel Hub |
 |
| Need 2 Pcs 5x10x4mm Ball Bearing Use New Ball Bearing Old Bearing maybe loose or dirty with Sand |
 |
| I am using a damage Wheel Axle from a broken UJ, 2.11mm Pin, Hex Wheel Adapter, Alum 4mm Flanged Nut |
 |
| A 4.5mm Hinge Pin, 3.9mm Turn Buckle, 3.1mm Ball End, 1.7mm Ball End |
 |
| 2x 2.5mm screw with washer and Nut, 2.2mm Screw, 3mm Screw with Nut |
 |
| All the Parts Needed |
 |
| A Water Gauge |
 |
| A Alum Plate |
 |
| All The Parts Needed |
 |
| Put the 5x10x4 Ball bearing into the Wheel Hub |
 |
| Use 3mm Screw to tighten the Wheel Hub to the Lower Arm |
 |
| Put in the Wheel Axle |
 |
| Put in the 2.11mm Pin on the Wheel axle is to hold the Hex Wheel Adapter |
 |
| Attach The Hex Wheel Adapter On the Wheel Axle |
 |
| Secure the Hex adapter from falling with a 4mm Flanged Nut |
 |
| The Finishing Parts |
 |
| Attach the Ball End on the Turn Buckle |
 |
| Attach the 1.7mm ball end on the Lower arm using the 4.5mm Hinge Pin |
 |
| Attach the Longer Ball End to the Wheel Hub Secure with the 2.2mm Screw do not tighten need to adjust |
 |
| The Finishing View |
 |
| Drill 2 hole on the end of the Alum Plate |
 |
| Tighten using two 2.5mm Screw |
 |
| The Finishing View on the Alum Plate |
 |
| Other Side View |
 |
| Remove the Wheel Axle, Using the Water Gauge to ensure the Wheel Hub is in upright Position, Turn the turn Buckle to adjust it, after the correct measurement tighten the Screw and fix back all the parts. |
 |
| The Finish DIY RC Wheel Balancing |
 |
| Rear View |
 |
| The View |
 |
| RHS View |
 |
| The View |
 |
| Found a Pcs of shape metal. So Transfer the Wheel Balancing on it. More smaller easy to Carry around |
 |
| Side View |
 |
| Top View |
 |
| Add Weight under to make it heavy |
 |
| Two pcs weight from my fishing Tool Box |
 |
| Side View with the buggy wheel |
 |
| Rear View More Smaller |
 |
| Making a Compartment Under The metal With Thin Alum Plate. |
 |
| Front View |
 |
Under View
|
 |
| Add a small box to keep the wheel balancing materiel |
 |
| Inside The Box |
How to use it. Remember that when turn the wheel should freely. Wait until it almost stop if the wheel rotate up and down that mean ur wheels un balance. Put some weight or raisin on the bottom of the wheel and then turn the wheel again, if at the end the wheel still rotate up and down add more weight until u get the wheel turn smoothly until stop no up and down.
On 7/10/2020 i redo this wheels balancing. Use bigger front suspension set from Hobao T058 all new part. Same assembly but improve.
ENJOY RC HAVE FUN
Comments