To control the steering and fuel or other devise in rc car, plane or boat for GP or EP, we need a receiver and servo. The Radio modulation from AM (Amplitude Modulation) This channel have more interference. FM (Frequency Modulation) This channel reduces risk of glitched. PCM (Pulse Cod Modulation) The most accurate signal possible 2.4GHz the simple and unique channel. only marching the ID code in the receiver. The signal given from the controller the Pistol grip or radio stick to receiver and activate the servo, that can control the car. Some toy grade we call remote control because need long wire to sent signal to motor. Mosly call Radio control is using frequency no long wire.
For my self until today i still using AM channel a simple not much problem due to many new RC car come with 2.4GHz system so there is no fear to use it. I am not a pro racer so no need to buy a high tech Radio control. For my Brand i will choose FUTABA and SANWA to match my RC car.
Today i have
For my self until today i still using AM channel a simple not much problem due to many new RC car come with 2.4GHz system so there is no fear to use it. I am not a pro racer so no need to buy a high tech Radio control. For my Brand i will choose FUTABA and SANWA to match my RC car.
Today i have
2 units Sanwa Blazer Am27,
2 units Sanwa Seven Ace AM27,
3 units Futaba MJ 2PH AM27,
1 unit Futaba Magnum Junior 2PKA AM72, 1 Units Futaba Attack T2ER AM40.
In 2013 i buy another radio control Made in China FLYSKY 2.4HZ FS-GT3B 3 Channels remote RM150.
Start bloog = 30/11/2012
Total units own =17
No 1 and 2. SANWA BLAZER 2 units.
The Sanwa Seven Ace Spec.
Output :
Modulation : AM/PPM
Power Supply : 8AA Alkaline Dry Cells DC12V
Weight :
Receiver Type
Model : SRD- 2122RS
Modulation : AM/PPM
Intermediate Frequency :
Power Supply : DC6.0-8.4V
Weight :
Dimensions :
Servo Spec
Model :SRM 102
Power Supply : 6.0V
Dimensions :
Weight : 50.1g
Speed : 0.20sec at 6.0v
Torque : 3 kg
No 5,6 and 7. FUTABA MJ 2PH. 3 unit
The FUTABA MJ 2PH Spec.
Output :
Modulation : AM
Power Supply : 8AA Alkaline Dry Cells DC12V
Weight :
Current Drain : 250mA
Receiver Type
Model : R122JE
Modulation : AM
Intermediate Frequency :455kHz
Power Supply : 4.8-8.4v
Weight :16.6g
Dimensions :47.2 x 33.3 x 17.3mm
Current Drain : 30mA at 4.8v
Servo Spec
Model : S3003
Power Supply : 4.8v or 6.0V
Dimensions :40.4 x 19.8 x 36mm
Weight : 37.2 g
Speed : 0.23sec at 4.8v
Torque : 3.2 kg
No 8. FUTABA ATTACK 2ER.
No 9. My FUTABA MAGNUM JUNIOR FP-2PKA
1. 3 Channels
2. Model type- Car and Boat
3. RF Power- No more then 10MW
4. Modulation- GFSK
5. System Type- AFHDS
6. Sensitivity- 1024
7. Low Voltage Warning less then 9.5v
8. DSG Port- 3.5mm
9. Charger Port
10. Power- 12VDC 1.5V 8PCS
11. Weight- 395g
12. Ant lenght- 26mm
13. Size- 154/127/270mm
14. Colour- Black
No 12 and 13. HSP 2.4 HX 2 units
Start bloog = 30/11/2012
Last Update bloog = 20/6/2024
Total units own =17
1) Am radio control = 12
2) 2.4Hz radio control = 5
 |
| 2018 pictures |
No 1 and 2. SANWA BLAZER 2 units.
First together with my Kyosho V one S and the second unit buy in flea market Seremban.
The Blazer Radio Control Spec.
Output : 500mW
Modulation : AM/PPM
Power Supply : 8AA Alkaline Dry Cells DC12V
Weight : 440g
Receiver Type
Model : SRC- 2322RS
Modulation : AM/PPM
Intermediate Frequency : 455kHz
Power Supply : DC6.0-8.4V
Weight : 32g
Dimensions : 52L x 33.5W x 19.1Hmm
Servo Spec
Model : Heavy Duty Standard Servo
Power Supply : 6.0V
Dimensions : 20L x 39W x 36Hmm
Weight : 45g
Speed : 0.18sec at 6.0v for 60deg rotation
Torque : 3.3kg
No 3 and 4. SANWA Seven ACE 2 Units
The Blazer Radio Control Spec.
Output : 500mW
Modulation : AM/PPM
Power Supply : 8AA Alkaline Dry Cells DC12V
Weight : 440g
Receiver Type
Model : SRC- 2322RS
Modulation : AM/PPM
Intermediate Frequency : 455kHz
Power Supply : DC6.0-8.4V
Weight : 32g
Dimensions : 52L x 33.5W x 19.1Hmm
Servo Spec
Model : Heavy Duty Standard Servo
Power Supply : 6.0V
Dimensions : 20L x 39W x 36Hmm
Weight : 45g
Speed : 0.18sec at 6.0v for 60deg rotation
Torque : 3.3kg
 |
| The Manual Book |
 |
| Sanwa Blazer Made in China |
 |
| The Front with Steering Wheel |
 |
| BLAZER Ergonomic Conception . |
 |
| Back View |
 |
| Back View |
 |
| The Steering Wheel |
 |
| Led Power Indicators Full Battery in best Condition |
 |
| Led Red Low Battery are dead or week |
 |
| The Grip Handle |
 |
| Power Switch |
 |
| Transmitter Crystal |
 |
| Antenna |
 |
| Throttle/Steering Adjustment |
 |
| Reversed Switches |
 |
| Throttle Trigger Position Gauge |
 |
| NICD Charger Jack |
 |
| Throttle Trigger Adjustment Screw. |
 |
| Steering Trim |
 |
| Throttle Trim |
 |
| Transmitter Battery Compartment |
 |
| With open Slide Cover |
 |
| The Battery Compartment |
 |
| With 8AA Battery |
 |
| SRS 2322RS Sanwa Receiver AM27 |
 |
| The Servo Sanwa 102 |
No 3 and 4. SANWA Seven ACE 2 Units
This my first Radio control for my Kyosho GP Spider. second from my secondhand kyosho GP SPIDER buy from friend. I didn't have the owner manual, i forget to take it from the shop boss.
The Sanwa Seven Ace Spec.
Output :
Modulation : AM/PPM
Power Supply : 8AA Alkaline Dry Cells DC12V
Weight :
Receiver Type
Model : SRD- 2122RS
Modulation : AM/PPM
Intermediate Frequency :
Power Supply : DC6.0-8.4V
Weight :
Dimensions :
Servo Spec
Model :SRM 102
Power Supply : 6.0V
Dimensions :
Weight : 50.1g
Speed : 0.20sec at 6.0v
Torque : 3 kg
 |
| Sanwa Seven ACE Made In Singapore |
 |
| Front View |
 |
| Sanwa Seven ACE |
 |
| Back View |
 |
| SANWA |
 |
| The Handle Grip |
 |
| The Antenna Compartment With a closing lid |
 |
| Open Lid |
 |
| The Antenna |
 |
| The Throttle Trigger |
 |
| Steering Wheel |
 |
| Transmitter Crystal |
 |
| Steering Dual Rate |
 |
| Steering Trim |
 |
| The Power Switch |
 |
| Nicd Charger Jack |
 |
| Throttler End Point Adjustment |
 |
| With a closing lid for Reverse Switches |
 |
| The Open Lid |
 |
| Reverse Switches |
 |
| Battery Full Power |
 |
| Battery Low Power, the led will blink and a buzzer will on |
 |
| The Battery Compartment |
 |
| The Open Cover |
 |
| 8AA Dry battery |
 |
| With the Battery |
 |
| The Servo SRM 102 |
 |
| Sanwa Receiver SRD 2122RS |
No 5,6 and 7. FUTABA MJ 2PH. 3 unit
Made in China. buy all new
The FUTABA MJ 2PH Spec.
Output :
Modulation : AM
Power Supply : 8AA Alkaline Dry Cells DC12V
Weight :
Current Drain : 250mA
Receiver Type
Model : R122JE
Modulation : AM
Intermediate Frequency :455kHz
Power Supply : 4.8-8.4v
Weight :16.6g
Dimensions :47.2 x 33.3 x 17.3mm
Current Drain : 30mA at 4.8v
Servo Spec
Model : S3003
Power Supply : 4.8v or 6.0V
Dimensions :40.4 x 19.8 x 36mm
Weight : 37.2 g
Speed : 0.23sec at 4.8v
Torque : 3.2 kg
 |
| The box |
 |
| Side view |
 |
| The speck |
 |
| Inside the box |
 |
| The piston grip |
 |
| The Manual |
 |
| FUTABA MJ |
 |
| Front View |
 |
| Back View |
 |
| The Steering Wheel |
 |
| Nicd Charger Jack |
 |
| Transmitter Crystal |
 |
| Power Supply Switch |
 |
| Throttle Trigger |
 |
| Steering Trim |
 |
| Throttle Trigger |
 |
| Grip Handle |
 |
| Antenna |
 |
| Trim Panel Cover |
 |
| Steering D/R adjustment for under or Over steers |
 |
| Steering EPA to adjust servo Movement |
 |
| Throttle EPA to adjust forward and brake servo travel |
 |
| Reversing for Steering |
 |
| Reversing for Throttle |
 |
| Power Switch from Inside |
 |
| Battery Level Indicator High |
 |
| Battery Level Indicator Low |
 |
| The Battery Compartment |
 |
| With Sliding Cover |
 |
| Inside The Battery Case |
 |
| With 8AA Battery |
 |
| Modified Version Using single 7.2V Battery |
 |
| The Servo S3003 |
 |
| The FUTABA Receiver FP-R122JE |
No 8. FUTABA ATTACK 2ER.
Buy together with my Kyosho Alpha Lazer is a stick type. Made in Taiwan. The only problem is the battery Cover is missing and the Receiver FP-R122JE only receive signal from 40.675MHz. I try using 27MHz Cristal can't receive.
The FUTABA ATTACK 2ER Spec.
Output :
Modulation : AM
Power Supply : 8AA Alkaline Dry Cells DC12V
Weight :
Current Drain : 250mA
Receiver Type
Model : R122JE
Modulation : AM
Intermediate Frequency :455kHz
Power Supply : 4.8-8.4v
Weight :16.6g
Dimensions :47.2 x 33.3 x 17.3mm
Current Drain : 30mA at 4.8v
Servo Spec
Model : S3003
Power Supply : 4.8v or 6.0V
Dimensions :40.4 x 19.8 x 36mm
Weight : 37.2 g
Speed : 0.23sec at 4.8v
Torque : 3.2 kg
The FUTABA ATTACK 2ER Spec.
Output :
Modulation : AM
Power Supply : 8AA Alkaline Dry Cells DC12V
Weight :
Current Drain : 250mA
Receiver Type
Model : R122JE
Modulation : AM
Intermediate Frequency :455kHz
Power Supply : 4.8-8.4v
Weight :16.6g
Dimensions :47.2 x 33.3 x 17.3mm
Current Drain : 30mA at 4.8v
Servo Spec
Model : S3003
Power Supply : 4.8v or 6.0V
Dimensions :40.4 x 19.8 x 36mm
Weight : 37.2 g
Speed : 0.23sec at 4.8v
Torque : 3.2 kg
 |
| Not my , found the box image |
 |
| The Manual Book |
 |
| FUTABA ATTACK T2ER Radio control |
 |
| Futaba T2ER Made In Taiwan |
 |
| Back View with Missing Cover. Modified a alum cover. |
 |
| Back View ATTACK |
 |
| The Antenna |
 |
| Power Switch |
 |
| Throttle Stick Forward and Backward |
 |
| Throttle Trim |
 |
| Steering Stick |
 |
| Steering Trim |
 |
| Servo Reversing for Throttle Stick |
 |
| Servo Reversing Switch for Steering Stick |
 |
| The Crystal |
 |
| Nicd Charging Jack |
 |
| Battery Level Indicator High |
 |
| Battery Level Indicator Low |
 |
| The Modified Battery Cover |
 |
| 8AA Dry Battery Compartment |
 |
| With Battery Position |
 |
| The Futaba S3003 Servo |
 |
| Futaba FP-R122JE Receiver Only Receive 40.675MHz Only |
No 9. My FUTABA MAGNUM JUNIOR FP-2PKA
Bought second hand from Taiwan. Made in Japan, In the beginning i think it came with the crystal but i receive no Crystal. The Problem is the Transmitter using AM72MHz. searching for this Chanel in RC shop no one have it . The original receiver using PP-R102GR but i get FP-R2GS. Know just leave one side may be i can get it one day the Receiver and Crystal.
The FUTABA Magnum Junior FP-2PKA Spec.
Output :
Modulation : AM 27MHz/ 72/75MHz
Power Supply : 8AA Alkaline Dry Cells DC12V
Weight :
Current Drain :
Receiver Type
Model : PP-R102GR (Ori)
Modulation : 75AM
Intermediate Frequency :455kHz
Power Supply : 4.8 - 8.4v
Weight :38g
Dimensions : 37 x 55.5 x 19 mm
Current Drain :
I have is
Model : FP-R2GS
Modulation : 72.870AM
Intermediate Frequency :
Power Supply : 4.8 - 8.4v
Weight :
Dimensions : 36 x 50 x 18 mm
Current Drain :
Servo Spec
Model : FP-S148
Power Supply : 4.8v or 6.0V
Dimensions :40.4 x 19.8 x 36mm
Weight : 44.4 g
Speed : 0.22 sec
Torque : 3 kg
No 10. KO PROPO EX5 MASTER 27Mhz (KT298AH)
The FUTABA Magnum Junior FP-2PKA Spec.
Output :
Modulation : AM 27MHz/ 72/75MHz
Power Supply : 8AA Alkaline Dry Cells DC12V
Weight :
Current Drain :
Receiver Type
Model : PP-R102GR (Ori)
Modulation : 75AM
Intermediate Frequency :455kHz
Power Supply : 4.8 - 8.4v
Weight :38g
Dimensions : 37 x 55.5 x 19 mm
Current Drain :
I have is
Model : FP-R2GS
Modulation : 72.870AM
Intermediate Frequency :
Power Supply : 4.8 - 8.4v
Weight :
Dimensions : 36 x 50 x 18 mm
Current Drain :
Servo Spec
Model : FP-S148
Power Supply : 4.8v or 6.0V
Dimensions :40.4 x 19.8 x 36mm
Weight : 44.4 g
Speed : 0.22 sec
Torque : 3 kg
 |
| FUTABA MAGNUM JUNIOR MANUAL |
 |
| Front View |
 |
| Front View |
 |
| Magnum Junior |
 |
| Back View |
 |
| Close Up Back View |
 |
| Steering Wheel |
 |
| The Throttle |
 |
| Grip Handle |
 |
| Antenna |
 |
| Power Switch |
 |
| Throttle ATV Low and ATV High |
 |
| Steering Trim |
 |
| Throttle Trim |
 |
| Steering Servo Reversing and Throttle Servo Reversing |
 |
| Steering Rate Adjuster |
 |
| Crystal Terminal |
 |
| Charging Jack |
 |
| Throttle Neutral Adjuster |
 |
| Battery Power High |
 |
| Battery Power Low |
 |
| Battery Compartment |
 |
| With Open Cover |
 |
| The Battery Holder |
 |
| Battery Holder 8AA Dry Battery |
 |
| Inside The Battery Housing 2 Terminal |
 |
| With Battery |
 |
| Inside the Housing |
 |
| The Original Receiver FP-R102GR |
 |
| I get a FP-R2GS Receiver |
 |
| The Servo FP - S148 |
No 10. KO PROPO EX5 MASTER 27Mhz (KT298AH)
On 3/10/2014 i buy second hand, AM Radio Control to match my Kyosho TF2 RC Car, Only problem with this radio no battery holder and antenna. Can't get the manual from Net, so all the data not sure. Another problem the steering control turn left the wheel go rhs, turn right the wheels go left. Need to change the remort wire. Setting on trim knob can't change it.
No 11. FLY SKY FS-GT3B 2.4HZ
 |
| KO Propo EX 5 Master |
 |
| The Steering Wheel without rubber grip, Modified one. |
 |
| The model |
 |
| The Throtter |
 |
| Trim button |
 |
| The On / Off Switch |
 |
| The turning wheel |
 |
| My First Digital Radio control |
 |
| Trim button |
 | |
| The Back View |
 |
| The Top View With Handle Grip |
 |
| Using Futaba Antenna |
 |
| The AM Cristal Location |
 |
| Brand sticker |
 |
| Serial number |
 |
| The Battery Location |
 |
| The Open Cover |
 |
| Removing The Battery Cassing |
 |
| Using the futaba Magnum Battery Holder, Need to Modified |
 |
| The Strip Hanger Hole |
No 11. FLY SKY FS-GT3B 2.4HZ
NEW Buy for RM150. Try up new frequency. The best is we can save 9 RC progrem use.
1. 3 Channels
2. Model type- Car and Boat
3. RF Power- No more then 10MW
4. Modulation- GFSK
5. System Type- AFHDS
6. Sensitivity- 1024
7. Low Voltage Warning less then 9.5v
8. DSG Port- 3.5mm
9. Charger Port
10. Power- 12VDC 1.5V 8PCS
11. Weight- 395g
12. Ant lenght- 26mm
13. Size- 154/127/270mm
14. Colour- Black
 |
| THE BOX |
 |
| On/Off Switch |
No 12 and 13. HSP 2.4 HX 2 units
Buy together with my HSP 1/10 monstet truck an 1/10 short course truck. A very simple 2.4 radio control system.
Channel = 2 channels
RF Power = less.then 20db
Modulstion = GFSK
Code type = Digital
Sensitivity = 1024
Low voltage warning = Yes below 9v
DSC Port = yes 3.5mm
Charging port = Yes
Power = 12VDC
Weight = 328g
Ant lenth = 26mm
Size = 159x99x315mm
Colour = Black
Receiver
Channel = 3 Chsnnel
Frequency = 2.4G
Modulation = GFSK
Sensitivity = 1024
RF receiver Sensiticity = 100dbm
Power = 4.5 to 6 vds
Weight = 5g
Ant lenth = 26mm
Size = 37.6x22.3x13mm
ESC
Model = WP1040 Brushhed
Cont/Burst Current = Forward 40A/180A. Backward 20A/90A
Input = 2-3Lipo, 5-9 cells Nimh/Nicd
Motor Limit = 2 Lipo or 6 Nimh = 540 or 550 motor over 12T, RPM Lest 30000@ 7.3v
3 Lipo or 9 Nimh = 540 or 550 size motor more then 18T. RPM Lest 20000 @ 7.2v
Resistance = FWD 0.002 OHM. BWD0.004 OHM
Build in BEC = 2A6V
Dimention = 46.5x34x28.5mm
Weight = 65g
No 14. Thunder tiger ACE RC JAGUAR 2 CH 8217.
Channel = 2 channels
RF Power = less.then 20db
Modulstion = GFSK
Code type = Digital
Sensitivity = 1024
Low voltage warning = Yes below 9v
DSC Port = yes 3.5mm
Charging port = Yes
Power = 12VDC
Weight = 328g
Ant lenth = 26mm
Size = 159x99x315mm
Colour = Black
Receiver
Channel = 3 Chsnnel
Frequency = 2.4G
Modulation = GFSK
Sensitivity = 1024
RF receiver Sensiticity = 100dbm
Power = 4.5 to 6 vds
Weight = 5g
Ant lenth = 26mm
Size = 37.6x22.3x13mm
ESC
Model = WP1040 Brushhed
Cont/Burst Current = Forward 40A/180A. Backward 20A/90A
Input = 2-3Lipo, 5-9 cells Nimh/Nicd
Motor Limit = 2 Lipo or 6 Nimh = 540 or 550 motor over 12T, RPM Lest 30000@ 7.3v
3 Lipo or 9 Nimh = 540 or 550 size motor more then 18T. RPM Lest 20000 @ 7.2v
Resistance = FWD 0.002 OHM. BWD0.004 OHM
Build in BEC = 2A6V
Dimention = 46.5x34x28.5mm
Weight = 65g
 |
| Blue colour |
 |
| Receiver |
 |
| WP1040Brushhed ESC |
 |
| Back view |
 |
| Other side |
 |
| Top view |
 |
| The trigel |
 |
| BOTTOM |
 |
| The control button cover |
 |
| The trim control and on/off button |
 |
| On |
 |
| Small antena |
 |
| The wheel |
 |
| Charging and DSC port |
 |
| Battery compartment |
 |
| Two with same colour so for short course Remort i spray red. |
No 14. Thunder tiger ACE RC JAGUAR 2 CH 8217.
Second hand togather with My Thunder tiger TS4N RC.
1. Jaguar 2AP
2. Product = 8217
3. Transmitter = JAGUAR T2P
4. Receiver = TR-202A
5. Servo = S1903
Transmitter
1. Frequency = 27MHz
2. Current Drain = 200mA@12V
3. Dimensions = 185×105×264mm
4. Weight = 395g
Receiver TR202A
1. Channel = 2
2. BEC = Yes
3. Single Conversion = 455Khz
4. Channel Spacing = 20Khz
5. Battery = AAX4@6v
6. Current Drain = 35mA
7. Dimension =48×34×22mm
8. Weight = 25g
Servo ACE S1903
1. Control =Pulse with Control
2. Operation Range = +-45 degree
3. Power Supply = 4.8 - 6 V
4. Current Drain = 10mA
5. Torque = 3KG
6. Transit Time = 0.19sec
7. Dimension = 40.9x20x37mm
8. Weight = 46g
No 15 Radio Control System TAMIYA ESPEC SP TTU-03.
1. Jaguar 2AP
2. Product = 8217
3. Transmitter = JAGUAR T2P
4. Receiver = TR-202A
5. Servo = S1903
Transmitter
1. Frequency = 27MHz
2. Current Drain = 200mA@12V
3. Dimensions = 185×105×264mm
4. Weight = 395g
Receiver TR202A
1. Channel = 2
2. BEC = Yes
3. Single Conversion = 455Khz
4. Channel Spacing = 20Khz
5. Battery = AAX4@6v
6. Current Drain = 35mA
7. Dimension =48×34×22mm
8. Weight = 25g
Servo ACE S1903
1. Control =Pulse with Control
2. Operation Range = +-45 degree
3. Power Supply = 4.8 - 6 V
4. Current Drain = 10mA
5. Torque = 3KG
6. Transit Time = 0.19sec
7. Dimension = 40.9x20x37mm
8. Weight = 46g
 |
| Instruction Manual |
 |
| Front View |
 |
| ACE RC 8217 Jaguar T2P |
 |
| Back view |
 |
| Side view |
 |
| Trim and Acc button |
 |
| Lid battery indicator |
 |
| On /Off button |
 |
| The trigel |
 |
| Tlhe turning wheel |
 |
| Antena and rhs the am cristel |
 |
| Normal and reverse button |
 |
| Battery location bottom |
 |
| Battery charging port |
 |
| The AM receiver |
 |
| S1903 servo ACE RC |
No 15 Radio Control System TAMIYA ESPEC SP TTU-03.
Buy on 12/10/2018 in a box just the pistol grip no receiver, Servo, ESC, 7.2 Nicd battery and charger. Buy for Rm40 with the box.
Name -TAMIYA EXPEC SP
Model - TTU-03
Parts no - 45030
Year -2004
Receiver - TRU-01
ESC - TEU-101BK
Servi - TSU - 01
2 chanel - AM 27.04Mhz
Made in - Philippines
Already two week, another 14 days to go under stay at Hone Malaysia Covid 19. Take out all my Radio pistol grip and do cleaning and checking, all still function. 12 = Am and 3 = 2.4Hz
No 16. HSP 2.4hz
Name -TAMIYA EXPEC SP
Model - TTU-03
Parts no - 45030
Year -2004
Receiver - TRU-01
ESC - TEU-101BK
Servi - TSU - 01
2 chanel - AM 27.04Mhz
Made in - Philippines
 |
| The box front |
 |
| The box side |
 |
| The box side |
 |
| The box rear |
 |
| The box top |
 |
| The box bottom |
 |
| Only the pistol grip radio left in the box |
 |
| Designer by Hans A Muth |
 |
| Tamiya Expec TTU-03 |
 |
| Steering Trim and Throtter Trim |
 |
| Steering reverse seitch and Throttle reverse switch |
 |
| Transmitter Crystal |
 |
| The in/off switch |
 |
| Battery indicater |
 |
| Steering wheel, no rubber grip |
 |
| Throttle Trigger |
 |
| Side view |
 |
| Back view |
 |
| Side view |
 |
| Bottom |
 |
| Top view |
 |
| Antenna |
 |
| Battery location |
 |
| With 8 pcs battery |
Already two week, another 14 days to go under stay at Hone Malaysia Covid 19. Take out all my Radio pistol grip and do cleaning and checking, all still function. 12 = Am and 3 = 2.4Hz
 |
| All 15 set. |
 |
| I have 24 units RC, if each RC have their own radio pistol, now should have 3 roll of radio pistol. After using a 2.4hz more eszy. Just buy more Receiver. Use only 1 radio pistol that can progrem 10 units rc. |
 |
| All simple not expensive radio control pistol. |
No 16. HSP 2.4hz
Buy for Rm4.16 on 10/1/2021 in a bunch of rc parts. After checking still functions. This for my HSP 94118 kutiger, No recever, battery compartment already modified.
 |
| This units i will spay yellow colour . |
 |
| All 3 units, yellow for HSP 94118 Kutiger |
No 17. E FLY.HOBBY EX3S 2.4Mhz.
On 18/2/2021, looking for secondhand rc in S2 toys seremban 2, found a nitro 1/8 monster + some loose parts include this 2.4 radio pistol grip. The shop owner say is a damage units, i just want it, go back and cheak still can on, all function on display. Then try to bind, it assap the signel but when turn steering and acc not function. Open up parts cheaking can't find fault, i thing frequency chip faulty.
 |
| Same as flysky radio control |
 |
| From E fly hobby. |
 |
| All same as fkysky radio pistol grip |
 |
| Side view |
 |
| On/off switch |
 |
| Rear view |
 |
| Bottom view |
 |
| Top view |
 |
| Steering wheel |
 |
| Lcd display and progrem ok |
 |
| Antenna |
 |
| Triggel |
 |
| Ear plug socket and charging port |
 |
| Selector butto |
 |
| Trim and steering |
 |
| Battery location |
On 6/3/2021, too boring all my project done few more waiting parts to arrive. Take out this radio pistol and dismental, connect to a rc car slowly touch all the terminal shake, press, the rc function, when fix back not function, remove the circuit board use sholder to melt some terminal led, check wire for break, fix back test ok all function, some time we can't see the loose terminal just solder. Yes another free radio control given to me damage, after do some checking can be use.
 |
| Fixing back after terminal solder, |
 |
| Some wire loose at wire antena |
 |
| Fix back parts, test again no fault |
 |
| Same product different company |
No 18. A Stick type Tamiya Temtech 201 2 channel Digital proportional RCS. With 27.195 Mhz. Old 1996 but new missing servo and receiver. After put in battery still can on, Made in Japan.
 |
| This not mine. Example complete complete set |
Enjoy RC
Comments
Adam smith
adam.smith402@yahoo.com
Nitrotek.se